Turbine Oil Cleaning System
KLAROL Turbine Oil Purification Systems are being successfully used by companies like Jaypee hydropower project in Joshimath, Indo Gulf Fertilizers, Jagdishpur, Daurala Sugar Mills and many more turbine users. In Indo Gulf Fertilizers, KLAROL Oil Purifying System installed on a 22000 litres turbine oil tank helped to increase turbine filter life by removing varnish formed in the oil and stopping its further formation by removing emulsified water and releasing the gas ammonia from the oil. Similarly in Jaypee hydropower KLAROL could clean the oil down to NAS 4,removing contamination and emulsified water down to less than 50 ppm, ensuring that there was no valve sticking problem in their governing system. Both these companies were unable to achieve these results with the use of a centrifuge. |
Unique features
KLAROL Oil Purifier can remove contamination down to less than one micron, water, air & gases and lower oxidised molecules of oil from turbine oils.
Removal of free and emulsified water prevents formation of varnish and bacteria. Turbine oil is 98% base oil and it has approximately 2% additives. By keeping the oil free from water and contamination down to less than a micron, KLAROL protects the turbine oil additives, which can then continue to perform their essential functions for a very long time thereby increasing oil life tremendously.
KLAROL replaceable filter element uses filter media which not only removes particles by depth filtration but it also has an affinity to remove varnish, sludge and lacquer from oil by adsorbtion.
The KLAROL filter is unaffected by water and can remove large quantities of contamination which makes it a very cost effective tool for removing contamination from turbine oils.
KLAROL can be installed directly on any turbine oil reservoir as a by-pass oil cleaning unit or it can be used as a mobile machine.
KLAROL mobile machines are fitted with pump / motor, pre-heater, vacuum pump etc to clean oil in the parent machine oil tank or outside it in drums or other reservoirs.
Removal of free and emulsified water prevents formation of varnish and bacteria. Turbine oil is 98% base oil and it has approximately 2% additives. By keeping the oil free from water and contamination down to less than a micron, KLAROL protects the turbine oil additives, which can then continue to perform their essential functions for a very long time thereby increasing oil life tremendously.
KLAROL replaceable filter element uses filter media which not only removes particles by depth filtration but it also has an affinity to remove varnish, sludge and lacquer from oil by adsorbtion.
The KLAROL filter is unaffected by water and can remove large quantities of contamination which makes it a very cost effective tool for removing contamination from turbine oils.
KLAROL can be installed directly on any turbine oil reservoir as a by-pass oil cleaning unit or it can be used as a mobile machine.
KLAROL mobile machines are fitted with pump / motor, pre-heater, vacuum pump etc to clean oil in the parent machine oil tank or outside it in drums or other reservoirs.
How Does KLAROL Turbine Oil Cleaning Works ?
KLAROL cleans oil in two stages using
three different methods. In the first stage oil enters the KLAROL depth filter to be cleaned by Absorbtion. All solid contaminants upto five microns are removed in this stage. The oil then passes at a controlled flow rate into the KLAROL evaporation chamber which is heated to ensure a dry airspace. Controlling the flow of oil through KLAROL ensures formation of thin oil film in the evaporation chamber. These conditions, i.e. Dry airspace and thin film condition are ideal to evaporate moisture, lower oxidized molecules of oil, air & gases from the oil. Purified oil then goes back into the parent tank. The KLAROL fibre glass depth filter removes insoluble contamination like sludge, varnish, and particles smaller than a micron by Adsorption i.e. (attracting and trapping the contamination in its filtering medium) when oil is continuously cycled through KLAROL. The KLAROL Oil Cleaning Systems are designed to remove contamination in stages and the continuous cycling of oil through it ensures that the smallest size contaminants are removed to provide super-clean oil in the parent machine.
three different methods. In the first stage oil enters the KLAROL depth filter to be cleaned by Absorbtion. All solid contaminants upto five microns are removed in this stage. The oil then passes at a controlled flow rate into the KLAROL evaporation chamber which is heated to ensure a dry airspace. Controlling the flow of oil through KLAROL ensures formation of thin oil film in the evaporation chamber. These conditions, i.e. Dry airspace and thin film condition are ideal to evaporate moisture, lower oxidized molecules of oil, air & gases from the oil. Purified oil then goes back into the parent tank. The KLAROL fibre glass depth filter removes insoluble contamination like sludge, varnish, and particles smaller than a micron by Adsorption i.e. (attracting and trapping the contamination in its filtering medium) when oil is continuously cycled through KLAROL. The KLAROL Oil Cleaning Systems are designed to remove contamination in stages and the continuous cycling of oil through it ensures that the smallest size contaminants are removed to provide super-clean oil in the parent machine.
Mobile Cleaning System
Permanent Installation
Technical Feasibility
At the moment Turbine Oils are cleaned by centrifuges which remove contamination and free water. Then, why do we need the KLAROL Oil Purifier for cleaning turbine oils ?
A centrifuge cannot remove emulsified water from turbine oils, which acts as a catalyst to increase oxidation, causes foaming in oils and reduces component life. One of the major problems of continuous water presence in the oil is formation of varnish which is a thin, insoluble film deposit that is usually found on bearings and servo-valves. It is a high molecular weight substance that is insoluble in oil. Varnish insoluble are more than 75 percent soft contaminants that are less than 1 micron in size and are not measured by traditional particle counts. Insoluble compounds have polar affinities and, over time, begin to migrate from the body of the base oil to machine surfaces.
Initially, the surfaces start to show a golden / dark brown color which then changes to darker gum layers that hardens into lacquer.
Varnish cannot be removed by a centrifuge. It can choke turbine oil filters,servo pencil filters, reduce bearing life, cause servo and directional valves to stick and fail and can even cause turbine shut-down.
Varnish’s propensity to attract dirt and solid particle contaminants increases component wear. Varnish’s insulation effect causes loss of heat transfer in heat exchangers
A centrifuge cannot remove emulsified water from turbine oils, which acts as a catalyst to increase oxidation, causes foaming in oils and reduces component life. One of the major problems of continuous water presence in the oil is formation of varnish which is a thin, insoluble film deposit that is usually found on bearings and servo-valves. It is a high molecular weight substance that is insoluble in oil. Varnish insoluble are more than 75 percent soft contaminants that are less than 1 micron in size and are not measured by traditional particle counts. Insoluble compounds have polar affinities and, over time, begin to migrate from the body of the base oil to machine surfaces.
Initially, the surfaces start to show a golden / dark brown color which then changes to darker gum layers that hardens into lacquer.
Varnish cannot be removed by a centrifuge. It can choke turbine oil filters,servo pencil filters, reduce bearing life, cause servo and directional valves to stick and fail and can even cause turbine shut-down.
Varnish’s propensity to attract dirt and solid particle contaminants increases component wear. Varnish’s insulation effect causes loss of heat transfer in heat exchangers
Permanent Installation
KLAROL Oil Purifying machines should be installed permanently on all turbines specially steam and hydro with high probability of water contamination.
Water and metal contamination act as catalyst to increase oxidation in turbine oils. This leads to formation of sludge and varnish which choke servo pencil filters and cause sticking of valves thereby resulting in turbine shut downs.
Studies by Timken bearing company reveal that even 100 ppm of water can decrease bearing life considerably.
Installing a KLAROL system permanently to continuously clean oil while it is in operation ensures that the oil is always free of water and metal contaminants. Continuous cleaning of the oil also ensures removal of the by products of oxidation which not only polymerise into sludge and varnish but with water and metal as catalyst further increase oxidation of the oil.
Installing KLAROL permanently on a turbine oil tank to continuously clean oil would help in maintaining the cleanliness level of oil at NAS 4 at all times.
KLAROL Oil Cleaning Systems should specially be permanently installed on oil tanks which supply oil to the turbine governing system. Continuous removal of sludge and varnish and reducing further generation of the same, by Klarol, would prevent choking of the servo pencil filters and sticking of valves thereby ensuring smooth turbine operation.
Water and metal contamination act as catalyst to increase oxidation in turbine oils. This leads to formation of sludge and varnish which choke servo pencil filters and cause sticking of valves thereby resulting in turbine shut downs.
Studies by Timken bearing company reveal that even 100 ppm of water can decrease bearing life considerably.
Installing a KLAROL system permanently to continuously clean oil while it is in operation ensures that the oil is always free of water and metal contaminants. Continuous cleaning of the oil also ensures removal of the by products of oxidation which not only polymerise into sludge and varnish but with water and metal as catalyst further increase oxidation of the oil.
Installing KLAROL permanently on a turbine oil tank to continuously clean oil would help in maintaining the cleanliness level of oil at NAS 4 at all times.
KLAROL Oil Cleaning Systems should specially be permanently installed on oil tanks which supply oil to the turbine governing system. Continuous removal of sludge and varnish and reducing further generation of the same, by Klarol, would prevent choking of the servo pencil filters and sticking of valves thereby ensuring smooth turbine operation.
When playing in} in a web-based on line casino in Korea, have the ability to|you possibly can} encounter many authorized issues and payment methods, so getting help becomes indispensable. That is why in most of the greatest Korean casinos, 빅카지노 on-line support is available 24/7. Below you will discover information on discovering the most effective on-line casinos for Korean gamers.
Trả lờiXóa